A biological formulation for use
in WWTP`s.
EC-2295 aids in
the recovery from toxic shock caused by phenols
and other aromatic compounds in Waste Water Treatment
facilities. |
PRODUCT DESCRIPTION:
Typically,
the susceptibility of biomass to upset depends primarily on
the magnitude of change in phenol concentrations. EC-2295 is
a microbial formulation for use in treating wastewater
containing phenols and related aromatic compounds such as
cumene, catechol and cresol. EC-2295 contains microbial
strains capable of uninhibited growth at high phenol
concentrations. Applicable processes include, but are not
limited to, steel coking, coal conversion, petroleum
cracking, plastic resins and pharmaceuticals.
BENEFITS:
•
Enables
rapid recovery from toxic shocks caused by phenols and
associated compounds.
•
Reduces or
eliminates upsets that resulting from variable phenolic
loadings.
•
Reduces the
inhibitory effects of phenols by increasing the growth rates
and sustainability of phenol degrading biomass.
•
Reduces the
negative impact of production increases on effluent quality.
•
Degrades
various halo substituted aromatics such as bromo and
chlorophenols.
•
Improves
stability as measured by the quality and variability of
biological effluents through the introduction of microbial
strains with higher growth and substrate utilization rates.
FEATURES:
•
Contains
vegetative and spore forming microbial strains capable of
utilizing aerobic, facultative and fermentative metabolic
pathways.
•
Does not
contain raw enzymes, surfactants, VOC’s or solvents.
•
Enables
rapid germination & spore outgrowth.
•
Adheres to a
variety of surfaces & supports biofilm formation.
|
|
|
|
PRODUCT CHARACTERISTICS
|
|
|
Plate Count |
5 X 109 |
|
Stability: |
<1.0 g/yr Typical |
|
pH: |
6.0 – 8.5 |
|
Bulk Density: |
0.50 – 0.61g/cm3 |
|
Moisture Content: |
7.1% Typical |
|
Appearance: |
Free flowing, granular powder |
|
Class |
NON-HAZ |
CONDITIONS
FOR USE:
Effective pH range: 6.0 – 9.0.
Optimum pH 7.0
Microbial activity is affected by wastewater temperature.
Microbial growth doubles with each 100C (180F)
increase in wastewater temperature to an upper limit of 400C
(1040F), unless otherwise indicated. Microbial
activity is significantly reduced at temperatures below 50C
(410F).
TYPICAL APPLICATIONS:
New plant start up
Post shut down and start up
Seasonal maintenance i.e. cold climate conditions
TYPICAL
APPLICATION RATES:
|
Treatment Plants |
|
|
|
Flow Rate |
Initial Dosage |
Maintenance** |
|
Up
to 0.1 L/sec |
0.5kg/day for 3 days |
0.5
kg/week |
|
Up
to 0.5 L/sec |
0.5kg/day for 3 days |
1.0
kg/week |
|
Up
to 2 L/sec |
5
kg* |
1.5
kg/week |
|
Up
to 5 L/sec |
8
kg* |
2.0
kg/week |
|
Up
to 25 L/sec |
15
kg* |
0.25
kg/day |
|
Up
to 50 L/sec |
25
kg* |
0.5
kg/day |
|
Up
to 100 L/sec |
50
kg* |
1.0
kg/day |
|
Up
to 500 L/sec |
50
kg/100 L/sec* |
1
kg/100 L/sec/day |
|
Up
to 1200 L/sec |
50
kg/100 L/sec* |
0.75
kg/100 L/sec/day |
|
Up
to 10,000 L/sec |
30
kg/100 L/sec* |
0.5
kg/100 L/sec/day |
**
Add as regularly as possible. If it is required to miss one
day, add that day’s product with the next dosage. Dosage
rate will vary with flow rates, retention times and system
variations. The rates above are for a typical, well
maintained system.
ACTIVATED
SLUDGE SYSTEMS:
Activated sludge systems include, but are not
limited to, extended aeration, contact stabilization, step
aeration, oxygen activated sludge. The application rate for
activated sludge systems is based on the average daily flow
rate to the aeration basin, excluding the return sludge
stream. For seasonal or widely fluctuating flows, contact
our technical representatives.
TRICKLING FILTER AND ROTATING BIOLOGICAL
CONTACTORS:
The application rates are based on the
average daily flow rate to the filter or contactor,
excluding any re-circulating process stream.
LAGOON SYSTEMS:
For aerated lagoon systems, the application
rate is based on the average flow to the lagoon.
|
Day
1-5 |
20
kg/10,000m2/day |
|
Day
6+ |
2
kg/10,000m2/week |
For anaerobic lagoon systems application
rates are based on total volume
|
<200,000 L |
1 kg
–2x/week per 10,000L |
|
>200,000 L |
0.5
kg –1x/day per 10,000L |
SAFETY:
The materials used in the production process are derived
from naturally occurring and sustainable sources. EC-2295 is
environmentally safe, is not harmful to animals, plants and
humans and does not contain chemicals of any kind.
COMPLIANCE:
Fully complies with EPA Toxic Substance
Control Act (TSCA) and the rules, orders and regulations
promulgated there under including:
a) Sections 4, 5, 6 & 7; Title 40 Chapter 1, 707.20 thru
707.75;
b) 40 CFR Sections 704.3. 710.2(e) and 720.3(c); and
c) Sections 5 and 13, reference 42FR64583
d) Does not contain marine pollutants as defined in 49 CFR
171.8.
PACKAGING:
8.8 oz. (250 g) Water Soluble Pouches - 22
Lbs. / HDPE Pail
Bulk – 22 Lb. (10 kg) HDPE Pails
Bulk – 100 Lb. (45.3 kg) Fiber Drums
STORAGE & HANDLING:
Store in a cool dry place away from direct
sunlight. Avoid creating dust in confined areas. Wash hands
thoroughly after handling. No special handling required.
Product Code: 6629
Class: NON-HAZ
Designation: Commercial /
Industrial
Application:
Bioaugmentation - WWTP’s (Phenols)
Packaging: 22 lb. HDPE Pail (44 WS Pouches/Pail)
Form:
Granular
|
| .gif)
